Simple Ways to Lessen Your Electricity Bills

After the mortgage of appliances or devices, electricity bills grab the highest income portion. Unfortunately, it is not possible to make it zero, until we cut the power connection. Which is not possible. Therefore, the aim of every owner is to cut these bills at least half. Considering your concern, in this write-up, we have highlighted the simple and easy ways to lessen your electricity cost. By following them regularly, you will find a great cost difference in your power bills within a month.

Buy Energy Efficient Appliances

When things come to shopping for appliances, many of us prefer to reduce our acquisition cost and go with cheaper options. But, do you think it's a wise decision? As per expert advice, appliances are used more frequently at homes and offices. Therefore, buying an expensive appliance will be a good decision if it will be able to cut power bills. For this, you can also check the National Environment Agency rating by tick system. Higher the green ticks, the better device to save energy cost. Don’t forget to check out these tick labels.

Lower the Appliances Temperature

Lowering the appliance's temperature can save your bucks. There are some easy techniques for you:

When you are not at home or at night, you can lower your room heater temperature. At night you can get under the blanket to stay warm.
In winters, lowering your refrigerator temperature is also a great way to save from high bills. You can even power off your fridge in between as it will not affect your food.
Reducing dishwasher temperature is also another way to escape from high electricity bills. So, it's good to change the hot water temperature level.
In summers, along with AC at the moderate temperature, you can also use a ceiling fan to control hot weather.
As per the US Department of Energy estimates, you can lower your bills by 1%, if you lower one degree of thermostat temperature.

Change Lights To LED

These days, there is a number of manufacturers producing high quality LED bulbs. Replacing them with traditional bulbs can save up to 30% of the amount of the bill. Moreover, these have a longer life compared to incandescent bulbs. In a study, it was observed that these bulbs can last for an average of 100,000 hours. And expected life is 15 years if used wisely i.e six to eight hours per day. Using LED bulbs means you are contributing to the environment safety also.

Measure Your Appliances Loads

Whether it is a dishwasher or washing machine, every appliance has a certain capacity to handle the load. Overcrowding will cost you through electricity bills or can even damage the appliance. Therefore, it’s good to check your appliance load before using them unwisely. You can also look at their manual or can take assistance from Google. In many countries, there are peak hours prescribed for electricity usage. Know your countries hours and avoid using heavy appliances during that time.

Replace Electric Wiring on Time

Old electric wires are also a great cause for increasing power bills. Timely replacement can helps you to save appliances, power issues and electricity costs. So, if 20-25 years have been passed to your wiring, keep in mind it’s the right time to replace it with quality wires. Importantly, never try to install wiring own, call a professional like boss electrical can help you for safe and secure installation.

Service Your Appliances Regularly

The next biggest thing that affects your bills is your appliances service. The regular visit of experts is important to keep your appliances in running condition and cut power costs. Appliances like AC, dishwasher, stove, refrigerator, microwave and many more require timely service for smooth running. This will also prevent your further breakdown costs.

Bottom Line

Hope, the above mentioned simple ways of lessening your electricity will help you. Try these for a month, you will definitely get fruitful results. For more assistance, you can also approach an expert like Boss electrical Group. Their rich experience in the electrical service will help for reducing the home as well as office electricity bills.

Air Conditioner Is Blowing Warm Air- How To Fix

The air conditioner is blowing warm air - this is a common issue and could be in a new AC. Therefore, don’t worry. If your AC is new, this can be due to changed settings or excessive heat outside. But, if your old air conditioner has such problems then check out some of its parts before calling experts like the boss electrical group in your area. Some of includes, dirty air filters, incorrect thermostat settings or low refrigerant. So, the below post help you to deal with these concerns.

Excessive Rush To Hosts 

Before you begin to find out the reason for warm air, familiarize yourself with the air conditioners operating information. Check out, how much time it is prescribed by the manufacturer in users manual to start air conditioner functioning properly. 

According to manufacturer climate control conditions also affect your air conditioner. If the outdoor temperature is more, then AC surely takes time to start cooling. Many owners of the appliances cannot wait for the air conditioner to start, they demand immediate result. Keep in mind, the process requires time to equalizing the pressure level. For this, the best solution is to wait for 10-15minutes before start fixing any issue.

If after the aforementioned period of time has passed, the device does not start functioning, then only then can a fault be assumed.

Dust Particles On Filter

Another common cause of poor device performance is the build-up of dust particles and other contaminating elements on the filter.

It should be understood that the traditional air conditioning system contains several levels of filtration of air masses. This ensures the formation of a comfortable microclimate in the room and protects the radiator from the effects of contaminating elements. Therefore, in the absence of regular cleaning of the above filters, the owner of the air conditioner may experience that the device stops heating. So, in order to keep the device again working condition, it is necessary to remove the filters from it and clean them. If the filter is presented in the form of a mesh, it must be washed in warm water using detergent. After the mesh dries, it is set to its primary position. 

To get rid of this problem, the impeller must be removed and wiped with a damp cloth. To carry out these manipulations should be very careful because you can damage the fragile details of the impeller.

Other Reasons Why Air Conditioning Does Not Work On Heating

If the air conditioner does not work , then it’s not a matter of rushing or dirtying the filters. These are signs that your air conditioner needs service. You should pay attention to the following reasons: 

1. Contamination in the heat exchanger of the outdoor unit. In those situations when the external unit of the device accumulates a large amount of dust, insects, fluff, the device may cease to produce heating of the air masses. Due to these contaminations, a huge load is created on the device, as a result of which it can fail. To prevent such a problem, you should regularly clean the external unit of the air conditioner.

2. Freon leakage. Even with the best quality air conditioner installation, 6–8% freon is still leaking during the year. In order to continue device functioning properly, it is necessary to refill the equipment with freon once every 1.5–2 years. If refuelling is not performed for more than 2 years, then the amount of freon in the device will fall below the required level. Such a situation will lead to the fact that the compressor will overheat and jam. It should be noted that the price of the compressor is almost 50% of the cost of a new air conditioner. To identify a similar problem, it is enough to look at the device, if frost is observed on the outdoor unit (its choke connections), and the air masses in the room are not sufficiently cooled, then there is not enough freon in the device. It’s impossible to fix this problem by yourself. So, don’t forget to call an expert like boss electrical.

It is important to understand that if your device has ceased to function properly, then panic will not help you. Carefully examine the problem, and if none of the above reasons is suitable, then contact the service centre.

Ways To Find Best Air Conditioning Service Provider in Australia

Are you searching for someone who can fix your Air conditioner malfunction? You don’t need to search on many websites. Here, we will discuss great tips to find the best repairman in your area. So, don’t miss a single tip as you may miss the opportunity to find serviceman. Let’s begin now:

What you can’t miss:

Online Approach
Yellowpages
Websites searches
Reviews are must
Local guide

Offline Approach
Directly approach to company
Call the nearby service centre
Consult with friends and neighbour
Check their referral results

Other parameters that need to be checked
Licence
Experience
Budget
Timing
   
Online Approach

Today, everyone has smartphone. Therefore, one can conveniently start their search by using internet services. Some of the best searches will be as follow:

Yellowpages

Yellowpages is one of the most used websites to search for any service provider. With an appropriate keyword search, this website provides you numbers of a serviceman in your area. You can conveniently check their details including the area of service, rating and past customers reviews. All the reviews about serviceman are posted by a genuine customer. Therefore, you can conveniently rely on them.

Websites Searches

Your another area of search could be websites. These days, creating own business website to be more visible on the internet is on high demand. So, you will get detail for many good options like the boss electrical group on it. Reading the website detail help you to judge the company’s profile and scope of business operation. Moreover, you will also get detail for past experience and other services.

Local Guide

There is also a local business listing on Google or other major search engines. These listings help the users in particular are. Simply use keyword “air conditioner services near me” will assist you for many options. You can take check out service centre rating and reviews for genuine results. Google also guide these servicemen with their location.

Offline Approach

The offline approach is from the family of the traditional approach. But this approach is more reliable as guided by users own experience. Here, we have some details for this search:

Direct Company Approach

This is the conventional approach of reaching to the service provider. Here you directly call to the company from where they buy their air conditioner. This is a highly suggested service provider. But if you need air conditioner service, its like icing on the cake. So, do not hesitate to call them during the warranty, otherwise, they could be a little bit costly. As they have complete knowledge for a product, therefore you can easily rely on their services.

Call the Nearby Service Centre

There can be many nearby service centre in your area or in the local market. Taking their services can be a good decision. You will have the benefit of availing their service as per your convenience and can easily lodge a complaint in case of any fault.

Consult with Friends and Neighbour

The near and dear one is the real advisor for any solution. Then why not to take their suggestion for your air conditioner. Surely any of their appliances met with malfunction and they too hire a repairman. Taking their help will help you a lot. In addition, your neighbour, friend or colleague's personal experience with an expert will also help you in framing the right opinion.

Check their Referral Results

While searching for a serviceman, you may meet with numbers of options. So, do not rely solely on their words. You need to check their suggested referrals of past customers. Consult them and find out the issues so that the same may not happen with you.

Other parameters that need to be checked

If you have done with the research work and want to scrutinise your choice then you must check the candidates on below-mentioned parameters.

Licence

Licence is one of the most important documents and needs to be with every service provider. Licence showcase the authenticity of expert and also define their area of work. In addition, a licence holder is also considered as a well-qualified person that knows about his job and responsibilities. So, while hiring a electrician do not forget to check his licence of . Most importantly, licence expiry date also matters so pay attention to that also.

Experience

As it is enough to be qualified, but experience has its own importance. First, experience persona always comes with the required tools and equipment. Second, he can easily deal with sudden issues and do not hamper or leave your air condition open. Therefore, many people suggest calling boss electrical in Australia. Because they have a team of experienced professional that can handle any issue.

Budget

Cost cutting is the aim of every individual. Therefore, while hiring a professional, it's good to discuss the cost of repairing in advice. An experienced serviceman hearing about appliance issue on the phone can give you an estimate for total repairing. Taking their benefit will help you to go with the budget. Importantly, always low budget is not a good factor. As some charges hidden charges in their repairing and others use low-quality material. Therefore, before appointing a person to be clear about taxes policy, whether they are included or excluded in service.

Timing 

Timing is the key. In the busy schedule, it's hard to take spare time for appliance repair. So, you can easily search for the serviceman that can provide service at your doorstep as per your convenience. There are many companies that provide round the clock services but charge a little higher. Or you can also go with weekend service providers if till date you can survive without an air conditioner.

Finding and appointing a serviceman can be a little tricky. You need to be aware of all the searching modes and master in scrutinising your choice. Best tip, do not forget to take service warranty card after taking service. This will support you from any malfunction arise of repaired parts.

Electrical Motor Installation Tips

Installing and repairing electrical equipment like motor requires complete knowledge about the technical procedure. One wrong installation step can make it vibrating, fails the bearings and even engine can be stuck.


Therefore, it is commonly seen that people tend to hire experts like boos electrical group to perform the proper electric motor installation procedure. Some of the key rules for installation of electric motors are as follows:

Rule To Know Before Installing The Engine

Before installing the engine for electrical installation, it is necessary to carry out test (preventive) work. Otherwise, any malfunctions discovered in the future, then all work done will be in vain.

When installing the motor one must consider the following key areas:

• Remove dust and dirt from the electric motor, carefully inspect accessible internal parts and check for irrelevant objects in it;
• Blow the electric motor with dry compressed air at a pressure not exceeding 2 kg / cm2. When blowing an electric motor of an open design, in order to save winding insulation from damage, keep in mind hoses with metal tips should not be used. If there is no compressed air, you can use any even an automobile compressor;
• Rotate the rotor of the electric motor manually to make sure that it rotates freely and that there is no jamming and knocking.

Electrical inspection

Electrics need to check the compliance parameters. So, it is necessary to check:

• Measure the insulation resistance of the megger with a voltage of 500 V. An electric motor with a winding insulation resistance below 0.5 MΩ must be dried. The minimum insulation resistance of the stator winding after drying at 60 ° C should be at least 0.5 MΩ;
• Check if the mains voltage corresponds to the voltage indicated on the rating plate of the electric motor;
• Check the system attached to the motor, the correctness of future connections of all terminals help in building an optimal motor connection to the network.

Installation of The Electric Motor on The Frame

Now, its a time to install the electric motor on the frame. Most often, this is how the electric motors of pumping plants and machinery are installed.

• Place the coupling half on the motor shaft, while correcting select the key under the keyway.
• Install the engine on the frame, aligning the motor shaft with the equipment shaft in height and axially.
• Fasten the installed engine to the frame with bolts and nuts of the required size.
• Check all mechanical fastenings of the electric motor (bolts, mounting bearing shields, foundation bolts, etc.) and, if necessary, tighten them.

Installing The Motor on The Frame With A Belt Drive

There is also a belt drive (transmission) required for installation. Most often, this method of mounting an electric motor is used in work with fans and some machine tools.

• Put the pulley on the motor shaft, while correctly selecting the key under the keyway.
• With a belt drive, the electric motor is mounted on a sledge;
• The electric motor should be mounted on the slide so that the axes of the shafts of the electric motor and the set in motion mechanism are horizontal and parallel to each other;
• The middle of one pulley should be against the middle of the other pulley,
• It must be possible to adjust the balance of the belt as it is drawn out, especially during the first operation time;
• The sledge must be level parallel to each other and aligned both in the longitudinal and transverse directions;
• The supporting surface under the sledge must be solid;
• For the belt balance, bolts must be provided to screw into the mobile stops.

Instead of Conclusion

• Check out the grounding of the motor base frame. The ground wire is clamped under the head of the bolt that secures the motor to the sledge or foundation frame. This contact point of the ground wire with the frame must be cleaned of paint, rust or another insulating coating;
• Connect wires to the electric motor from the switching device ( starter, controller, electric machine ). After connecting the wires to the engine, check the reliability of contacts leads of the electric motor with joining wires;
• Once again, check the correctness of the pairing (alignment) of the shafts of the electric motor and drive;
• Manually scroll the motor shaft again;
• Applying voltage to the engine.

For more info, do not forget to call boss electrical. 

5 Key Points That Indicate That Your Air Conditioner Needs Service

Cleaning once in a year is essential to prolong the life of the air conditioner. Some of its components like filters, coils, fins, drains etc. get damage or blocked due to regular contact with dust particles. Therefore, your negligence in service can lead to great damage to your unit.

Let’s know some of the alarming symptoms that demand its cleaning by professional.

1. No Cooling

When the air from the vent is not cool as expected, therefore its a sign that you need to call an expert. This could be also an indicator that its compressor has been damaged or it's refrigerant level is too low. So, servicing at the right time can save your equipment from being damaged.

2. Higher Electricity Bills

Higher electricity bill is another major cause of aircon servicing. This is also an indicator that it is not performing its function properly. Therefore, it needs to take more load to maintain your comfort level. In addition, if its outdoor unit is placed at somewhere where you can some unusual noises, it's a clear notification that it demands to call boss electrical.

3. AC Blowing Dust While Turning On

Even though you have maintained your air conditioner properly. There are high chances that dust can build in the nooks and crannies of your air conditioner. This reduces your air-con efficiency and lowering air quality. In addition, choking dust also affects your inner environment. And results in puffing of dusting and difficulty to breathe in the room. Dust can also make worse conditions to survive in air conditioner room. You need the immediate air conditioner cleaning.

4. Leakage

Leakage in aircon is of two types refrigerant and water leakage. Refrigerant leakage is dangerous for the people and animal’s health. Whereas, when the water starts coming out from your air conditioner, this is called water leakage. It happens mainly due to clogged drain tubes. Water leakage is not harmful as of refrigerant but your ignorance can damage your air conditioner.  

5. Bad Smell And Strange Noise

Your air conditioner some times produce a bad smell that could be a sign of burnt wires. In such a case, its good to immediately turn off the air con and call an expert. Whereas, many times you may hear about unusual noises produce by your unit like some material is grinding. This is an emergency situation and power of it to prevent further damage. This could be a symbol before completely failing your appliance.

Final Word

It is essential to catch your air conditioner issues at first instance. Your AC acts as an investment in tangible and intangible form. So, investing in timely maintenance will help you to save your device from replacement. This will not improve its quality but reduces your electricity bills too. All this can happen if you hire a professional from an experienced company like a boss electrical group. That believe in customer satisfaction.

5 Tips To Verify Before Hiring An Electrician

Lights sparkling? Had circuit breaker broken? Outlet on the stopped working? or something unusual happening to your electrical appliances or wiring. Keep in mind, it's not the right time to showcase your DIY skills. Its a case of emergency and you need to call a nearby electrician who can deal with this issue. But, if you are going to build new or want to repair the existing home. You will have plenty of time to choose a good electrician like the boss electrical group. For this, you can also set a questionnaire in your mind to avoid any wrong choice. 

Build a Strategy Plan before Hiring

To perform wiring or rewiring function, you should make appropriate plans. The layout can include:

• Set your budget
• The time required to accomplish a job
• Work scope
• Payment options include timing, amount and selection of mode 
• Project start and completion date.
  
  The discussion on above will take only 5-10 minutes. But, these can save a lot of time and money. So, Think about them!!!

Things to Consider Before Hiring An Electrician

• Licence and Insurance of the Electrician It is mandatory for every electrician to have a licence before performing his job. The licence ensures you that the person you are going to hire have a good knowledge of his work. With this, you can also check on the internet about the authenticity and expiry date of the licence. And what are tasks he is eligible to perform under licence. In addition, to keep yourself on the safe side, you must also check the electrician's insurance. This will protect you, in case an accident happens.
  
• Type of Warranty Offered by ElectricianA good electrician always offers a warranty for the job done by him. The warranty assures you that he is sure about the job. The wires he used is of high quality and in the near future, there is no or very fewer chances of any misshapen. If something happens wrong, boss electrical is always there to support you. 

• Look for Their Experience
  An experienced person has fewer chances of conducting mistakes. He knows the right technique of performing the job in a short time. But, yes I am not saying, to not to hire a fresher. Because fresher will have knowledge about new ideas and aware of the latest power saving techniques. On the same side, I will add, you can hire a fresher that must have minimum one year experience. With this, you will too feel secure. 

• Check out the RecommendationA recommendation helps you decide or not to decide the electrician. Before, hiring ask him for the reference from his previous project completed. From there, you will get a practical idea that how the electrician performs his duty. Is he leave any loophole in the project or deliver without any issue on time. Sharing words with previous customers also build your confidence in an electrician. 

• Pay Attention To Their Behaviour
  
  Wiring in a new house or rewiring in the repaired house can be a long way process. This may take weeks. So, everyone loves to deal with a person having a positive and friendly attitude. If you are able to find such qualities in your electrician, it will be easy for you to explain your problem openly. But, if you find, your electrician has a contradictory approach. It’s good to leave in the first stage.

Wrap Up!!!

Hope, the above-mentioned five tips will help you to find the best electrician that can do a great job. Keep in mind, wiring or rewiring is a high-cost project. Therefore, many people afraid of hiring a person professional. Keep in mind, companies like boss electrical group offer high-quality services at affordable rates. So, there is no need to delay your plans. Just make a call to them for quality services. 

6 Signs That Indicate Poor Electrical Wiring At Home

Outdated wiring is not something that one should take it lightly. Every year a high number of cases becomes the newspaper headlines for residential and commercial electrical flaming. Don’t make your dream home to be part of these headlines. Every wire before letting the fire out indicate some signals, that alert you for the reinstallation of wiring. Some of them include high electricity bills and meeting with electric shocks frequently. If you notice any of these situations at your home then it's a high time to replace your wiring. Here we have some more indicator of poor electrical wiring at home:

1. Low Lightning

Dimmed lighting at home is not an indicator that there is an issue in the bulb. This clearly shows that there is a low power supply in the wires. Therefore, it becomes unable to illuminate properly. In such a case, it's better to switch off all your power connection and make a call to an electrician.

2. Smoke From Switches, Lights or Appliances

If you ever notice a smoke comes out from your outlets, lights or appliances. Don’t take it casually. As this could be the major reason for fire broke-out and your whole home can go into flames.

3. Noise Issue

Normally, electricity at homes runs without any noise. But if it is making some unusual sounds like buzzing, crackling or sizzling. Keep in mind, these are the indicator that you are using electricity more than the requires to load. This can affect the electric panel, fuse box or overload circuit.

4. Burning Smell

This is something that found occasionally when you notice the candle burning smell from your home. This means it is the initial stage of wiring melting. So, noticing and taking desirable action at an early stage help you to solve many issues.

5. Circuit Breaker Tripping

Its a common issue seemed in almost houses. That when they use either of the appliance, the circuit breaker trip. If this happens once in a while then it's ok. But if it goes on a regular basis then make it could be dangerous for your home. As there is a need to call boss electrical to make the best rewiring.

6. Discoloration Around Outlets

There could be a sign of discoloration seen on the outlet on the cover or the wall. This could be in the form of black or brown. It represents a major risk of electric flaming. So, fixing this issue as soon as possible is the best remedy to save your home.

Benefits of Rewiring

There are multiple benefits rewiring at your home. Most importantly, it saves your life that cannot be backed with money. Some of the other advantages include:

• It boosts the life span of your house’s electric wiring. On average, it is found that the life of wiring in any house is 20 years. Therefore, with rewiring, you blessed your home for the next 20years.
• With rewiring, you also stop malfunction to your electric appliances. As most of the appliances meet with voltage issue due to weak wiring connection.
• Rewiring also helps you to cut your power bills. As the new and safe wires consume less electricity and adding smart meters at home is the best way to save power and money.
• If you are going to take home insurance, remember your rewiring will help you cut insurance cost.
• Rewiring also becomes a center of attraction, even if you are going to sell your house. People consider this safety aspect on a priority basis.

Bottom line

If you notice above-mentioned the warning signals at your home, remember its a red alert for you to call the professional. Depending upon the situation, a professional electrician like boss electrical group takes the desired action at the initial stage and save your home, money and dear one’s life.